This guy's still for sale. www.thedealersden.com/listing/fire...

If this gets a few likes, I'll share the art and idea of what i plan to make.

This is still up for sale, You can haggle if you think the price is too much.

-Mori

Fire Shiba Inu - Head Fire Shiba inu Dog - Black, Grey, Red and Yellow Furred fursuit premade.

Fire Shiba head is up on Dealer's Den

Yay!

<3
-Z

www.thedealersden.com/listing/fire...

Me wearing it. I'm small so the neck bunches up a lot more than it should. But it will bunch up a bit with anyone.

Grey, black, red yellow dog fursuit head. Has a big nose. 3d printed teeth and a yellow mouth with fire designs in the fur. Yellow eyes with grey iris and black pupils.

Fire Shiba Inu head done.
Will be out as a head only item that you can add more money to, to get a tail and gloves.
The starting price will be 750 USD.

This is the second head I have ever made. So there ARE errors here and there. But they are not that bad.
Will be put up at 6pm PST.

-🪷Mori🪷

ko-fi.com/barkitup/shop Added a lot of old characters i have to my shop that i decided to sell. If you want to haggle feel free.

I finally got the spoons to work on the head again. Fixed the eyebrow and cheek where it was badly balding. Bad quality fur (red) was shaved a bit too close on and brushed and it balded.

But now. You can hardly tell what side is balded / was fixed lol

This will be for sale soon.

🪷-Mori-🪷

Box of LED strips shipment. Plan to stick 4800 LEDs on the ceiling to make a rave room in the living room.

16 rolls. 300 LEDs per roll.
Cut in half for 32 strips of 150.

These are all going on the ceiling to be controlled by a single custom controller.

Soon!

Apologies for lack of posts.
The whole house has been sick.

The 4800 LED ceiling project will be underway by the new year!

Much excite. Such LED.

<3
-Z

#FurFest

Gear looks to be working fairly well!
I'm slightly concerned on the red activity, may look at raising the upper limit of the sensitivity range ...

I got my X right next to a woofer...

Red is a little overactive... Maybe?

:3c

Late post for last night's content, but typical con stuff.
@furfest.org

7-point custom with leg strap add-on for @chocomage.bsky.social
Bonus collar and leash!

Bulldog 3-point with leash @riptyde.bsky.social

<3
-Z

Bulldog style 3-Point with optional collar and leash add-on(s) Zetta wearing pup gear and this lit LED gear.

X 4-Point Style Harness Zetta wearing fox head partial and lit harness.

'Standard' 5-Point Style Harness Zetta wearing pup gear in front of a mirror with harness lit in FFT mode

Going to MFF this weekend?

Keep an eye out for Zetta in 1 of 3 styles of harness.

Stop him for a hug!
Ask questions!
Check out the gear!

Ask him about the (soon to be) 4800 LEDs on his living room ceiling that will run off the same hardware he is carrying around!

Worried about the bag getting flagged so made a little demo box using the original hand-assembled PCB and the silicone seal test LED strip

Bag: through no issue
Zetta: flagged for additional pat down screening

TSA agent at the bins:
"What's that? Oh that's cool."

Zetta:
😰

<3
-Z

Bark It Up! - Order Request Form Thank you for your interest! There are a few things to note for the order process. === ORDER PROCESS === 1. Select your style 2. Fill out measurements (see guide below) 3. Submit form 4. We'll c...

IT'S HAPPENING!

MFF Launch Week is a GO!

Pre-orders are open NOW!

Put 'bsky' in the 'Special Requests and/or Feedback' section on the last page of the form for an extra 5% discount off the intro MFF launch pricing.
Payments and production to begin January.
barkitup.dog

<3
-Z

Pup waiting to go for walkies. LED bulldog style harness, leash, and collar.

Leash!

Just in time for walk time!

3 LED controller boxes charging off a single USB-C splitter cable. Power adapter rated for 5v 3A so can only charge 3 boxes at once. Need more power ...

Little 4 way USB-C cable inside a pack of rechargeable AA and AAA batteries at Costco.
It can charge 3 of my boxes at once on my 18w brick. (1A each charge rate)
Sadly it's sharing power to the USB-A and USB-C ports so I can't also charge my phone...
Will use the AA and AAA somewhere...

<3
-Z

Short LED leash in active electrical testing.

Getting bags ready for packing out of the garage.

Find spare material to make leash (or two?) in said bags.

Woo!

<3
-Z

Bulldog 3-point style harness with added collar displayed on a good pupper waiting to go for walkies.

Pending some materials to make an LED leash, here's the Bulldog style and collar on a good pup.

This will be 1 of 4 styles running around MFF.
Feel free to say hi!

<3
-Z

Remake!

The Leg Strap add-on for the last 7-Point build ended up a little too long.
These are 40 LEDs each down from 53.
Seal curing overnight then assembly tomorrow to get them out for MFF next week!

I'll have a few builds with me! Follow the lights if you want to chat!

Controller close up of push button being held. 6mm switch buttons used. Thumb for scale.

Close up of 3-pin JST connector used between collar and controller for wider use case and modular design.

Close up of controller JST connector. 3-pin style with the latch end used as the 'output' connector in most all my designs.

Modular 3-pin JST connector used.
Connects to harness/collar at specific input points.

Switching on, the LEDs will flash green and start in static FFT mode.

Press the button to switch modes.
Hold the button until the LEDs flash Red to lock.
Hold the button until the LEDs flash green to unlock.

Close up drawing attention to the low profile slider on/off switch. Button and USB-C on the face of the controller.

Close up showing the face of the controller (switched on with green LED in the background)

Controller bottom showing bottom plate removed and 18650 battery.

Controller top with plate removed showing the main electronics and control hardware.

Box!

Designed for easy use, even while wearing paws or mitts.

3d printed PETG enclosure.
Integrated clip.

Slide toggle switch for on/off.
Low profile to prevent accidental toggle.

Single push button to change or lock the mode.

Single swappable 18650 battery.

USB-C for run and/or charge.

New X design showing full length LED runs along both straps with a single O ring and hook and loop fastener to tie it together. (Lower straps loop through O ring at front to offer some adjustability

Close up of an adjustment point for the X 4-Point design. A square of hook on the end of the strap which is passed through the Chest O Ring. A length of loop strip lines the back of the LED strap for the hook to attach. (Amount of adjustability depends on design, roughly 6 inches here for clarity. Adjustment points on other designs will typically be a few inches to reduce bulky excess material that doesn't have LEDs inside)

Wide view of 7-point design with leg strap add-ons slightly visible on the left and secured to the main harness via hook and loop. Design incorporates buckles on the chest strap with slight adjustability points via hook and loop at the buckles. The connection points at both hips offer adjusted for the waist straps via hook and loop on the back straps. It also gives a more lightweight result with less buckle weight on top of the added few inches of fine tune adjustment.

A fox (Zetta) showing off the 7-point design. Leg straps not connected here to show the base design. 7-point meaning there's 7 straps that meet at the chest. <3

Work shopping some hook and loop for slight adjustability at some key connection points.

New X design

Allows the leg strap add-ons on the current MFF 7-point build to be modular

Will update with some better photos once the harness is on the fursuit it was measured for

Set for LAUNCH!

<3
-Z

Got a battery for the multimeter.
Power testing puts my 600+ LED and 6+ hour runtime estimates in the ballpark of EXTREMELY conservative.

TL;DR: there's enough juice to rave all night.
Also run+charge via power bank or swap 18650 batteries.
Either way, the power ceiling is HIGH.

<3
-Z

🔧 Tech specs:
- SAMD21 ARM Cortex-M0+ processor
- 12kHz sampling rate, real-time FFT
- Custom PCB (open source on GitHub)
- UF2 bootloader (drag-drop firmware/code updates)
- MCP73831 charging (1A safe rate)
- PETG enclosures (convention-durable)

Full docs: github.com/joshuawboone...

<3
-Z

*600+ LEDs at 1/8 brightness
**6+ hours tested with 300 LED test array

Dynamic sensitivity adjustment keeps all frequency ranges responsive regardless of music style or volume level.

<3
-Z

🦊 ZettaLights - Custom LED Harnesses

🎵 Real FFT analysis (8 frequency ranges)
⚡ 600+ LED capacity*
🔋 User-swappable 18650 (6+ hour runtime**)
🔓 Open source everything
💻 Custom engineered PCB

$650-1500+ | Standard or full custom
Pre-orders launch MFF weekend.
Production starts January.
barkitup.dog

FFT video of the X as a treat!

Gotta sew these up and run full battery life tests!

<3
-Z

7-Point 'Full' Style Harness with added Leg/Thigh straps. Back view. Rainbow LED mode.

7-Point 'Full' Style Harness with added Leg/Thigh straps. Side view. Rainbow LED mode.

7-Point 'Full' Style Harness with added Leg/Thigh straps. Front view. Rainbow LED mode.

Redesigned 'X' 4-Point Style Harness. Rainbow LED mode. Front view on workbench. New seamless style, O Ring only present on front. LEDs cross on the back along with the straps. Hook and Loop adjustability via the lower straps on the O Ring.

MFF prepping!
New 'Full' 7-Point Style! (with Leg Strap Add-on)
252 LEDs! (+106 LEDs = 358 LEDs)
Designed for a friend in fursuit so excuse the slack! :3

Redesigned 'X' 4-Point Style!
138 LEDs!

Let's gooo!

Harness still in front of mirror. Rainbow mode.

Side note:

Pre-orders will open MFF weekend for payment and processing to begin in January.
(Tax stuff)

Still need to process a few personal/gift builds for photos on the form and measuring guidelines/diagrams.

Want to make your own? Check the pin post. I've made everything open source.

<3
-Z