ah yeah RGBeters board, forgot about that 😂

just need @cosam-the-great.bsky.social for the pcb and the rest of the nomad case 😂

SEGA Nomad - External Battery (18650 + USB-C) by RetroGameRevival | Download free STL model | Printables.com

Surprise drop:

SEGA Nomad battery, with full instructions and PCB files + links, under free use (even commercial!).

www.printables.com/model/169409...

PCE Pac agter being recapped

Also thought i had audio problems with the PACS as tried 2 PCE pacs and no audio or faint.

But that was the PACS, they also need recapping.

The Sega PAC worked, but still needs recapping.

After recapping all the boards, this dead laseractive is now working.

Had some other faults along the way, mainly me, i didnt push the CONT connectors all the way in as was afraid to break them 😂.

This caused video problems with the PACS and CD’s did not spin.

@zaxour.bsky.social said to reflow
…

I finally finished up a circuit to better approximate the composite palette! Output from the bonanza goes in, then modified RGB goes out. Not necessary if you have an RT5X/4K, but would be useful for CRT's/other scalers.

A Pico based GX Cartridge for Amstrad GX4000 console allowing games to load from sdcards

Lovely Stuff

FSTB pcb from a pioneer laser active

CONT pcb from a pioneer laser active

Laser Active Update

FSTB and CONT done.

FSTB recapped no problems and no fishy smells surprisingly

CONT lost 2 pads and some fishy smells from a few caps

Might do the RGB later that will leave me with the VIDEO board over easter and cleanup and reassemble, if i remember where the cables went 😂

Accompanying yesterday's Genesis is this 32X - recapped and outfitted with a Buzzkill to ensure no inductor noise!

Ugly duckling Model 1 VA7 Genesis glow up with a 4BP and TS924 headphone amp! No more horribly balanced audio, with cleaned-up RGB and S-Video capability to boot! I opted for a bottom side install this time...wish I had a flex for everything 🫠

Annalog NES An NES Metroidvania Puzzle Adventure!

Just backed - Annalog NES
www.kickstarter.com/projects/ell...

Good luck on your Journey

*INTF

Print outs of consolemods page for the INTF board

Laser Active INTF board after recapping

Leaky boy

Started on my Laser Active Recapping Journey with the INFT

consolemods.org is an excellent resource.

Made Cap Box to help sort the caps i need.

C418 was the leaky boy that was stopping this board from working

Sega Genesis CDX maxed out with some brand new tech!

-Full Recap
-3BP w/ Flex Kit
-Mega Everdrive PRO Enabler
-FRAM

Other than a few minor tweaks, I'll be putting these kits into production soon!

NeoGeo AES - Replacement Shell by RetroGameRevival | Download free STL model | Printables.com

NeoGeo AES Shell replacement model is fully done (and tested by the amazing @chris-jh.bsky.social), and now available on my Printables!

www.printables.com/model/163908...

My Test Print

Hurray 😂

disappointed, no 8008135

I have one of yours bought few years back its great.

My friend wanted one and bought an Ali Special, it went back for a refund 😂

I sent an image of your post, he will be happy 🤣

So Close

PicoIDE it be amazing if it got to 1000%

at this moment in time it is handled by the front panel esp32 which also controls the front panel in general.

when all open source, you could make your own board with an esp32 to connect to the picoide base board

10 hours left for the PicoIDE, you can watch this video by Rees if you want to know more about the device

www.crowdsupply.com/polpotronics...

10 hours left

Will be test printing at some point, need to figure out best angle

nice tip and a tasty treat

Neogeo AES with original too case sitting on a 3d printed pink bottom case

NeoGeo AES 3D printed bottom

Some minor adjustments for @pointerfunction.bsky.social to fix, otherwise fits great 😁

The Sovol SV08 Max for me printed great.

yes there are VFDs but thats because i never calibrated it for them 😂.

I did buy a chamber heater for it, pain to fit as i need to access under it and its heavy and big

👀 👀 👀

NeoGeo AES bottom case preview on Orca

First couple of layers printed on the sovol sv08max

Close up and the vents

Doing a test print of a neogeo’s aes bottom by @pointerfunction.bsky.social in his favourite colour pink transparent petg 😂