0
1
0
0
Hashtag
#GMSL
Advertisement · 728 × 90
Minimal running #linux #yocto build for the new Kernel 6.12 now running on the #NavQPlus. Next time to move the #GMSL drivers over from #AD Analog Devices and see if we get further then with the older 6.6 kernel...
1
0
1
0
Short updated on progress on the #GMSL SerDes link: Switched directions on drivers, @ADI_News finally released an official driver for GMSL devices and now I'm porting them to the #NavQPlus. Main challenge is (lack of) documentation, and that drivers are for the #Linux Kernel 6.13
1
0
0
1
Slowly getting somewhere with the SerDes #GMSL link. Media chain and capture command working "without" error. Before failed at VDIOC_STREAMON.
Now it just does not progress from here when issuing a capture command. Looking now where in the chain the camera signal is broken.
#CV
1
0
0
0
SerDes GMSL link media chain
Further progress on the SerDes #GMSL link. Media chain (OV5645->MAX96717->Max96724->i.MX8MP) is now created successfully, but it fails when trying to capture frames. Further debugging required (soon almost all source files are filled with debug print statements)!
#NavQPlus #CV
3
0
1
0
After working a few weekends on the GMSL #SerDes link for my #GMSL boards, I have the drivers half working:
- MAX96724 driver from #NXP linux repo
- MAX96717 driver backported from #Linux repo (6.14 -> 6.6).
All devices load and show up but the V4L2 link is broken.
#SBC #imx #navqplus #rpi
3
0
0
1
New setup works very well, finally able to compile the NXP NavQ #Hovergames Linux image in useful time! Fresh compile took around 4h, its quite a heavily loaded Linux image.
Time to work on adding the #GMSL SerDes, with a LOT of learning on the way.
#yocto #linux #embedded #sbc
2
0
0
0
It's time to upgrade my home desktop PC, started to work on compiling Yocto for the #NavQPlus for the #GMSL SerDes Camera link project and it would take ages...
1
0
0
0
All components finally arrived for the 4-Channel #GMSL deserializer board I'm developing! All soldered now, after the holidays days, time to move to testing and software development!
PCB sponsored by #PCBx (www.pcbx.com?mtm_campaign...)
#cv #camera #pcb #hardware #embedded
2
1
0
0
ローデ・シュワルツ、GMSLベースのソリューション拡張による新たなテスト機能を発表 #ローデ・シュワルツ #ADI #GMSL
ローデ・シュワルツがADI社と連携し、GMSLテスト機能を強化。ADASやIVIシステムの開発が迅速に実現可能に。CES 2024でのデモにも期待。
0
0
0
0
Power supply part of the #GMSL deserializer soldered and working. Will test current capabilities to guarantee it works well for the application. In possible future iteration would try a PMIC instead of 3 discreet buck converters
#soc #cv #vision #emebedded
5
0
0
0
The PCBs for my #GMSL camera link project arrived! Thanks to PCBx for sponsoring the PCBs (www.pcbx.com?mtm_campaign...). The matt green finish looks great!
Now onto soldering components and then looking into the #linux drivers.
#embedded #sbc #computervision #rpi
5
0
0
0
While waiting for the #PCB (sponsored by #PCBX) for my #GMSL Link Project, I have been creating the project page on the Website.
For it I'm refreshing the design of the PCB "viewer", with new design for the hover and highlight feature.
#web #CSS #WebDesign #html5
6
1
0
0
A render of the stackup of the #NavQPlus with the 4-Channel #GMSL board. Looking into designing an enclosure for it, similar to a #Jetson AGX enclosure.
This combo will enable the acquisition of 4 cameras over the 2 MIPI interfaces of the NavQPlus, for a e.g. 360º surround setup!
#PCB #CV #Robotics
3
2
0
0
Camera side GMSL3 module (w. PoC) for the #GMSL link I'm working on. Uses the MAX96717 from analog devices on a "standard" 38x38mm camera module sized PCB. Connector for Google Coral Camera (OV5640), planning on creating adapter PCBs to other camera modules e.g. #RPI cameras.
#PCB #CV #NavQPlus #ML
2
0
0
0