I went to split keyboard meetup last weekend. Had a lot of fun there!
#MechanicalKeyboards
#ErgonomicKeyboards
#ErgoMechKeyboards
9
0
2
0
Hashtag
#ErgoMechKeyboards
Advertisement · 728 × 90
2
0
0
0
Assembly done!
Build time: 1.5h
Cleaning the entire room to find a solder: 4h
details in thead
#keyboard #ergomechkeyboards
5
0
2
0
PCBs, 3D prints, keycaps and some key switches
New #keyboard components arrived. 🥳
#ergomechkeyboards
4
0
2
1
Canonical tabby lying on a white duvet. Closer to the camera a split keyboard steeply tented is mounted on a small board with a trackpad between the keyboard halves, and a white cable loops off the board. The cat’s face rests perfectly within the loop.
You’d think the cable’s loop exists to indicate “Cat’s face goes here”.
#CatsOfMastodon #CatAndKeeb #ErgoMechKeyboards
3
2
0
0
A angular view of a flat, square-ish dark red trackball with raised buttons around the outside. In the center arises a relatively enormous cue ball, white with red spots. It's sitting on a desk.
A side by side view of two trackballs, both with the ball removed. One is purple and one is dark red. Each has 3 equidistant bearings that would normally hold up the ball. The purple one uses standard ball bearings in the wheel shape. The red one uses BTUs, a style of bearing that can rotate in any direction.
A side by side view of two trackballs, one purple and one dark red. The purple one has buttons flush with its face, and a much smaller (pink) ball. The dark red one has raised buttons. The two have somewhat different logos embedded between the two largest buttons.
The ball mysteriously disappeared from the Makerspace's trackball. I could have just ordered another, but they use this novelty size pool ball that you can't really get in high quality. So instead, I upgraded it to the Anyball mod for standard American sizes. Case […]
[Original post on pxlmo.com]
2
4
1
0
ZSA is really good at #keyboards 😍, and really bad at capitalism 😁. I broke a part on my #ZSAVoyager and emailed to buy a replacement PCB (1/3 the total cost of the board!). I didn't ask about using the warranty because I'd made some mods that voided the warranty ages ago, but they looked up my […]
0
0
0
0
66 key mechanical keyboard in gray case with beige and light gray keys, yellow special keys and a red rotary knob.
Well, now that my lily58 ergo mech board is down I'm falling back to my spare. It's an Epomaker TH 66 and its fine for a standard board.
I got to say though going from column staggered back to row staggered is not a happy place for me.
#ergomechkeyboards […]
[Original post on infosec.exchange]
0
0
0
0
Two halves of a grey split ergonomic mechanical keyboard. Left half is bare, a naked plate. Right halve has keys in beige, gray and blue.
I'm crushed. The left half of my lily58 ergo mech keyboard started flaking out yesterday. Once plugged in it types 5tgb and then those keys go dead. I'm thinking a short.
It's a boardsource.xyz buy, not quite a year old. I'm going to reach out but any […]
[Original post on infosec.exchange]
1
0
0
0
Zu viel kaputte Realität, zu wenig Keyboards.
• Endgame by Oldman
• Choc Sunsets
• LDSA Keycaps (endlich)
#customkeyboards #ergomechkeyboards
1
0
0
0
Interested in some unusual hardware? A few weeks ago, I've published a blog post about one: my new keyboard, the ZSA Voyager, and how I got to the point of buying one.
zoltanadamek.com/en/2025/01/z...
#ZSAVoyager #ErgoMechKeyboards
0
0
0
0
A laptop and ergonomic split keyboard on a black table. The table is shaded, but the light around is bright. The laptop sits on a stand, and the keyboard is in front of it with a trackpad between the two halves. Each keyboard half is tented to about 90°, and a coffee and cinnamon roll are close by.
The patio tables at most cafes make the perfect surface to put my magnetic keyboard stands on. 😁
#ZSAVoyager #ErgoMechKeyboards
4
0
0
0
A laptop and ergonomic split keyboard on a black table. The table is shaded, but the light around is bright. The laptop sits on a stand, and the keyboard is in front of it with a trackpad between the two halves. Each keyboard half is tented to about 90°, and a coffee and cinnamon roll are close by.
The patio tables at most cafes make the perfect surface to put my magnetic keyboard stands on. 😁
#ZSAVoyager #ErgoMechKeyboards
0
0
0
0
Cantor Remix with hand-crafted artisan cardboard tray case 📦 😂.
Been using this all week after fixing up the KLOR (resoldered some LEDs) #ergomechkeyboards
0
0
0
0
There is a whole community on reddit but be warned it's a rabbit hole lol
www.reddit.com/r/ErgoMechKe...
#ergomech #ergomechkeyboards
1
0
1
0